Unplug the unit. After a few minutes, plug the unit back in, turn the switches back on and give it one hour and recheck the water temperature If this does not correct the issue, please call our Customer Service Center.
Why is my primo not working?
Unplug the unit. After a few minutes, plug the unit back in, turn the switches back on and give it one hour and recheck the water temperature If this does not correct the issue, please call our Customer Service Center.
How do I get my Primo water dispenser to work?
Slide the bottle into the Primo Water Dispenser cabinet. Plug the water dispenser into a ground fault circuit interrupting outlet (GFCI) The water will begin to pump water into the hot and cold reservoirs. Turn on the desired functions in the back of the dispenser by flipping the switch on/off.
Why is water not coming out of my water dispenser?
The failure of a water dispenser to dispense water is usually caused by one of the following conditions: You have air in your water line Your refrigerator water line is not turned on. Your water filter cartridge needs to be replaced.
What are the 3 switches on back of Primo water dispenser?
CONVENIENCE SWITCHES – On/off switches for heating, cooling, nightlight and self-sanitization are located on the back of the dispenser. self-sanitization light – Flashes green when sanitizing. COOLING LIGHT – Flashes blue when water is cooling. Light turns off when water is fully chilled.
How do I reset my water cooler?
Option 3 – Try “resetting” your cooler by removing several cups of water from both the hot and cold taps and switch off the machine Unplug it from the wall and leave for 24 hours before switching it on again. Give the water temperature about 5 to 6 hours to adjust before dispensing to see if it worked.
Why is my cooler pump not pumping water?
With bottom-filled water coolers, a common cause of flow issues is a poor connection of the hose between the probe head (on top of the bottle) and the water pump ensure that the hose is fully inserted into both. If yours is a mains-fed water cooler, ensure the mains tap is turned on.
Why is my liquid cooler not working?
There are a number of reasons why your water cooler might not be working as it should. For example, there could be a problem with the power source Or, there could be an issue with the compressor or refrigerator. There might even be a problem with a dirty filter.
How do I fix my water dispenser?
- Straighten or Replace the Dispenser Tube
- Clean Out the Water Lines
- Inspect and/or Change the Water Filter
- Test the Water Pressure
- Defrost the Water Line
- Check the Pressure Switch
- Inspect for a Faulty Door Switch
- Replace the Control Board.
How do you clean a Primo Water Probe?
Pour the bleach (2 tbsp.) or vinegar (2 cups) and hot tap water (2 Gallons) into the empty bottle. Apply the cleaning bottle to the dispenser. Plug the power cord back into the wall outlet and turn the dispenser back on. Allow the cleaning solution to fill the reservoirs.
How do you fix an airlock in a water dispenser?
Airlock – This is a very simple problem that occasionally occurs with coolers that have just been installed or serviced. The cooler simply needs to be reset. This can be done by holding down/pressing both taps at the same time for a couple of minutes to allow the air to escape.
Why is my water filter not working?
Check that the threaded area where the filter will connect to the refrigerator has nothing blocking the small holes where the water will flow through Sometimes part of the wrapping on the new filter itself could possibly block the water flow. If something is blocking flow, this will cause low flow.
How long does a primo water cooler last?
Primo water dispensers should last as long as the bottles are kept and serviced properly. However, the average lifespan of the primo water dispenser is not more than 6-12 months.
Do Primo water dispensers only work with Primo Water?
A: You can use any water bottle I have been using this product for the past 6 years and I have about 8 water bottles all different brand and I never have any problem so far.
Why does my ice maker work but not the water dispenser?
Frozen Tank or Tubing : The water reservoir tank or tubing could be frozen. If frozen, you would get water to the icemaker but not the dispenser. The water reservoir tank or tubing is typically located behind the vegetable drawers or on the left side of the fresh food compartment.
What is red button on back of Primo water dispenser?
Red full indicator in tray rises when tray is full indicating it’s time to empty Water Bottle – Not included. Uses 3, 4 or 5 gallon bottles. Visit www.PrimoWater.com to find Primo Water at a store near you.
Where is the self cleaning button on a Primo water dispenser?
Visit www.PrimoWater.com to find Primo Water at a store near you. green control to OFF to stop cooling. Self-Cleaning Switch – Located on back left Press IN, hold for 3 seconds and release to activate the cleaning cycle.
How do I know if my liquid cooling pump is working?
The only way to accurately determine if your Liquid Cooling Pump is functioning, is by checking the Pump RPM This will only be possible if the pump cable is connected directly to a fan header on the motherboard.
How does a cooler pump work?
The Pump Brings Water to the evaporative cooler pads After there is enough water in the bottom of the evaporative cooler, the pump begins to pull water through the water distribution lines. These water distribution lines are located at the top of the evaporative pads and pour water through them.
How do you prime a swamp cooler pump?
Allow Cooler to Run Before Turning on Blower Like a car engine runs best when allowed to warm up, your swamp cooler should have run time before the blower is turned on. Waiting about 15 minutes to turn on the blower allows the system to get the water circulating and to prime the pump.
Why does my swamp cooler keep turning off?
Make certain that the electrical wiring and connections on your swamp cooler motor are secure and not overheating themselves or shorting out. Also, a bad switch in the swamp cooler motor or fuse can cause the motor to get hot and shut off.
Why is my air cooler not working?
The most common reason the evaporative cooler may not be giving a good air flow is because of the circuit breaker and fuse of the evaporative cooler , which are installed by the manufacturer to prevent damage to the unit. If there is a power surge, you can be sure that the unit will not be damaged.
What are the parts of water dispenser?
- A tank (or two)- to store the water to be heated or cooled prior to dispensing.
- A water heater- to heat the water.
- A refrigerating system- to cool the water.
- A tap or spigot- to release water.
- A button or knob- for users to dispense water.
Can a water dispenser overheat?
Over 12,000 Nestlé Waters AccuPure floor standing filtration dispensers have been recalled because the dispensers can overheat and smoke, posing fire and burn hazards.