Despite their high cost, most prosumer espresso makers come with a throw-away plastic tamper, but that is not the case here. The Pro 500 includes a hefty steel tamper (2). It also comes with two commercial grade 58 mm portafilters, a single spout, a double spout, and matching single and double baskets.
Which is better double boiler or heat exchanger?
A two group, dual boiler machine can effectively double your capacity With this type of machine you could have two baristas brewing and steaming at once, solving speed issues you might be experiencing. They are also more precise than heat exchangers because of the dedicated boiler.
What is an E61 group head?
E61 group heads are an espresso machine group head design that have been around since 1961. It’s a design that is very tried and true and is one that is used on many of our prosumer grade espresso machines and even some commercial machines like the faema legend and the Faema Jubile.
How long does it take for the Profitec 500 to heat up?
Get it Good & hot turn on the machine. Lock the portafilter into the group head. Wait 30 minutes Take this time to start reading up on how to brew and froth below, if this is your first machine or you’re new to pulling shots.
Do I really need a dual boiler?
So who needs a Double Boiler? Double boilers do have an advantage There’s less difference in temperature between cups, so you are likely to have more consistent shots. When one draws a lot of hot water from the steam boiler, it also won’t affect the brew temperature as much.
Can you brew and steam at the same time with heat exchanger?
Unlike a single boiler, heat exchange machines can brew and steam at the same time as there is a separate water path for the brew water and the steam. They have one big boiler (means good, consistent steam), with a heat exchange pipe that runs through the centre which feeds the grouphead.
How important is PID on espresso machine?
PIDs can be very important in espresso machines as they provide temperature stability and consistency If you have been following Owly Choice, you must know that the perfect temperature is essential in brewing espresso. When water is too hot, it burns coffee beans and thus causes over-extraction.
What size is an E61 portafilter?
This new ergonomic 58mm portafilter is built in Italy and is made entirely of stainless steel, including the spouts. This portafilter is deep enough to hold any size VST basket, including the 22 gram.
What is a Grouphead?
Essentially, the group head is the part of the espresso machine where water from the boiler is dispensed into the coffee filter basket It acts as a meeting point, connecting the machine to the group handle and the water to coffee.
Who makes the E61 group head?
Since, the E61 is now off patent, there are several manufactures of this brew head to include Gruppo Cimbali (Cimbali Group) who now own the the Faema brand and VBM (Vibiemme) who used to own the Faema brand in there early 1970s.
What temperature should I set my PID for espresso?
The optimal temperature for espresso extraction is between 90 and 96°C (195/205°F) If you set a hotter temperature, it’ll result in higher extraction yields (and burnt coffee, if using boiling water), whereas colder brew temperatures mean that less coffee is extracted at a slower rate.
Is a dual boiler coffee machine worth it?
Dual boilers represent the best of the best, but are more suitable to those with large budgets and the kitchen bench space to house their large size , while heat exchangers are more suitable for the home baristas who want to make a great brew while more sensitive regarding price and space.
What is a thermoblock?
thermal blocks, also known as thermo blocks, are essentially a block of metal with a small passage or torrent that allows water to pass through This block is heated using an embedded heating element, which heats the block to a suitable coffee temperature as the water is passing through.
Are heat exchanger espresso machines good?
A heat exchanger is a good espresso machine for someone that drinks primarily milk-based drinks and for someone that tends to use the same beans repeatedly (limiting the need to adjust brew temperature).
When should I replace my Grouphead?
- Purpose: To maintain a proper seal between the grouphead and the portafilter basket when extracting espresso.
- Frequency: If your machine used greater than once every 3 days, every 6 months, or if your machine used less than once every 3 days, every 12 months.
What is an E61 group head made of?
The E61 is made of solid brass The heat exchanger and a Thermosyphon system circulate hot water through the brew group, keeping it constantly heated. The significance of the E61 brew group is the mechanism in the brew head which allows for the pre-infusion of the grounds.
What is the purpose of a bottomless portafilter?
Bottomless portafilters allow the barista to instantly deduce whether proper tamping technique has been achieved If the extraction leans to one side or the other an improper angle was used when tamping.
Does the Profitec 500 have a shot timer?
The PID in the Pro 500 doesn’t have a shot timer so there’s no sense in displaying the PID on the front of the machine.
What is meant by tamping coffee?
Tamping is the method a barista will use to take a loosely dosed amount of coffee grounds and turn them into a tightly compressed, evenly dispersed puck within the portafilter, where the water and coffee will come in contact when it’s brewing.
Where is Profitec made?
The production Our espresso machines and grinders are manufactured in our production facilities in Bammental and Mauer (near Heidelberg) We assemble each part by hand. We want you to be satisfied and therefore we work with the greatest care and passion on every single detail, for the perfect espresso machine.
What’s a double boiler look like?
Simply put, a double boiler is just two pots: a large one that looks a lot like a regular saucepan and a smaller, more shallow pan that nestles inside To use one, you fill the bottom pan with an inch or two of water and set the shallow pan on top.
Is a single boiler espresso machine worth it?
The benefit of a single-boiler espresso machine is that it is generally cheaper than a heat exchange espresso machine To make an espresso, a single-boiler machine has to change modes from coffee mode to steam mode, and there is an associated wait/drain time.
What is a HX boiler?
Heat Exchanger (HX) One boiler that heats water for brewing espresso and hot water/steam – and do allow you to use both functions simultaneously. The water in the boiler is superheated to create steam.
Why do I need a double boiler espresso machine?
With a heat exchange or dual boiler machine you can brew and steam at the same time Not only does that save you time but it makes a better milk-based drink as your espresso or milk froth doesn’t fall apart while waiting for that temperature change.
What is a dual boiler espresso?
Double boiler espresso machines are equipped with two boilers: a brew boiler and a steam boiler While the steam boilers reach and hold pressure ideal for frothing milk, the other maintains consistent brewing temperature.
Where are rocket coffee machines made?
ROCKET ESPRESSO Designed and hand-made in the heart of Italy , each machine is built for perfection and designed to integrate seamlessly into your kitchen.